Kramer-electronics TailorMade Manual de usuario

1KRAMERElectronicsMATRIX ROUTING SWITCHERTABLE OF CONTENTS 1 HARDWARE ...

10KRAMERElectronicsMATRIX ROUTING SWITCHERSET AUDIO GAIN for audio input Equal to input number (+ 80h) whose gain is to be set Gain value 32 steps:

11KRAMERElectronicsMATRIX ROUTING SWITCHERNOTES on the above table: NOTE 1 - These are bi-directional definitions. That is, if the switcher receiv

12KRAMERElectronicsMATRIX ROUTING SWITCHER 1 bal/unbal 1 G4 G3 G2 G1 G0 Where bal=0 and unbal=1 the reply to the HEX code 19h 82h 80h 81h would b

13KRAMERElectronicsMATRIX ROUTING SWITCHER 3 MATRIX HOOK-UP 3.1 MAINS AND GROUND ISOLATION The electric ground of all the plugs are the same, but is

14KRAMERElectronicsMATRIX ROUTING SWITCHER1- Ground 2- Hot 3- Cold 1- Ground 2- Hot 3- nc 1- Ground 2- Hot 3- Cold1- Ground 2- Hot 3- Cold 3.4

15KRAMERElectronicsMATRIX ROUTING SWITCHER4 GENERAL FEATURES 4.1 VIDEO SECTION - Bandwidth @ -3dB: 350 MHz - Crosstalk @ 4,43 MHz: -50 dB between

16KRAMERElectronicsMATRIX ROUTING SWITCHER5 TOUCH KEYBOARD : LUMINOUS RE-LABELABLE 5.1 PRESENTATION The keyboard permits the remote control of the s

17KRAMERElectronicsMATRIX ROUTING SWITCHER 6 INCREMENTAL TOUCH KEYBOARD AND LCD DISPLAY 6.1 PRESENTATION This keyboard permits the remote control

18KRAMERElectronicsMATRIX ROUTING SWITCHER7 MatrixOp4 SOFTWARE 7.1 INTRODUCTION The principle of the routing switcher is to connect each of its ou

19KRAMERElectronicsMATRIX ROUTING SWITCHER Source Object connected on an input of the switcher. Disconnect A destination is disconnected when there

2KRAMERElectronicsMATRIX ROUTING SWITCHER1 HARDWARE 1.1 GENERALITIES The Kramer matrix switchers are used to select and dispatch electric signals, a

20KRAMERElectronicsMATRIX ROUTING SWITCHER 7.4.1.1 Names and Connectors capture. Click on the line of a source or destination object. This window op

21KRAMERElectronicsMATRIX ROUTING SWITCHERThis mode of display is characterized by several personal lines corresponding each one at a destination, w

3KRAMERElectronicsMATRIX ROUTING SWITCHER 1.3 CREATING A MATRIX The rear panel of the rack is 19” wide, on 3RU high. The mains, RS232 and RS422 pl

4KRAMERElectronicsMATRIX ROUTING SWITCHERThe cards are horizontally located, and can be extracted by the front panel. Each card own up to 32 stereo

5KRAMERElectronicsMATRIX ROUTING SWITCHER2 COMMUNICATION 2.1 FORMAT Interface Speed (Bauds) DATA (Bits) Parity STOP (bits) RxD level TxD level

6KRAMERElectronicsMATRIX ROUTING SWITCHERtemporally stored in a stack FIFO (first-in first-out) with 2 levels records. To be sure not to overflow th

7KRAMERElectronicsMATRIX ROUTING SWITCHER2.3.2 RS422 Reception and Remote Control Panels The serial RS232 communication port of the matrix is a SUB

8KRAMERElectronicsMATRIX ROUTING SWITCHER 2.4 COMMUNICATION PROTOCOL 2000 TM INCLUDING OPTIONS (02/09/2005 VER-5.06) This RS-232 / RS-485 communic

9KRAMERElectronicsMATRIX ROUTING SWITCHER2nd BYTE: Bit 7 – Defined as 1. D6…D0 – “INPUT or DATA”. When switching (ie. instruction codes 1 and 2